2025 Vermeer® Horizontal Grinders HG4000TX

Information

2025 Vermeer® Horizontal Grinders HG4000TX

HG4000TX highlights
  • A mid-sized grinder with aggressive performance and capacity
  • Robust build quality for confident longevity
  • Maintenance-friendly design optimizes serviceability
  • Equipped with Vermeer innovations to protect your investment and optimize efficiency

Features may include:

Productive and powerful
  • The Series III hard-faced duplex drum offers durability and convenient maintenance, with the ability to remove and replace single hammers and balance the drum externally.
  • With a feed opening of 60 in x 30 in (152.4 cm x 76.2) and robust infeed sidewalls that are double the strength of its predecessor, you can feed whole trees and other large material with less restriction and minimal operator interaction.
  • The feed roller is equipped with aggressive teeth, coupled with down pressure, that provide pull-in power and maintain control of the material being fed to help get the job done efficiently.
Intelligent operation
  • The intelligent feed system self-monitors the machine's engine speed, makes predictive adjustments and holds the engine at an optimal level, allowing you to spend more time feeding and less time adjusting settings.
  • Machine damage caused by metal contaminants entering the hammermill can be costly. The Vermeer Damage Defense system helps protect your machine by detecting certain metal contaminants.
  • An industry-leading, full-function, wireless remote control lets you, from the cab, adjust machine settings as conditions change, including control of the infeed settings, engine droop, conveyor height and more.
Jobsite mobility
  • Increased onsite mobility with the track drive system allows for jobsite flexibility and reduced material handling requirements to optimize labor.
Your access to MORE
  • The VermeerOne™ platform isn’t just a tool or platform. It’s an experience — one designed to simplify equipment management, empower users with real time data to make smarter decisions, and help maximize productivity and profitability.
Integrated options
  • The Vermeer productivity monitoring system provides real-time data on machine performance and allows you to track the volume of material processed by visualizing cubic yards per gallon of fuel.
  • The Vermeer coloring system, fully integrated into the grinder, reduces the number of machines required and minimizes handling of material, adding value to your end product. This system optimizes dye and water usage, minimizing your cost per yard.

Photos

Highlights

  • La Crete, Alberta
  • 2025
  • Vermeer®
  • Horizontal Grinders HG4000TX
  • C13B T4F/Stage
  • Ultra-low sulfur diesel (<15 ppm)
  • Available
  • Feed Table: 60 in | Infeed Roller: 56 in | Millbox Opening: 60-in (152.4-cm) wide | Millbox Lid Liner: 62-in (157.4-cm) wide | Anvil: 13.6-in (34.5-cm) wide | Single Belt: 48 in
  • Loading: 6.4 ft | Millbox Opening: 30.5-in (77.5-cm) high | Millbox Lid Liner: 21.5-in (54.6-cm) high | Anvil: 6.1-in (15.6-cm) high | Load: 14 ft

Specifications

  • 2025
  • Vermeer®
  • Horizontal Grinders
  • HG4000TX
  • Horizontal
  • C13B T4F/Stage
  • CAT®
  • T4F/Stage V
  • 6
  • Gross (Maximum): 536 hp
  • 1807 ft-lb
  • Diesel exhaust fluid capacity 17.3 gal
  • Full-flow, spin-on
  • Medium: Liquid (nitrite-free, pre-diluted 50/50)
  • Track Drive: Two-speed bent axis axial piston
  • Max Fuel Consumption: 27.2 gph
  • Ultra-low sulfur diesel (<15 ppm)
  • Clutch: Hydraulic-operated twin disc | Engagement: Push button
  • Fixed displacement motor | Motor: Fixed displacement motor/planetary
  • Track: Hydraulic release
  • 8D-MHD, 1400 CCA (qty. 2)
  • 24 V | System Protection: Fused
  • 270 A
  • Drum: 1113 rpm / 842 rpm | Tip speed (Duplex): 9615 ft/min | Tip speed: (1-in chip) 7274 ft/min | Belt: 625 ft/min | Tracks - Maximum: 2.8 mph / Low Travel in Creep Mode: 1.4 mph
  • Air to boil temperature: 126 F (52 C)
  • Track Width: Ground Bearing Pressure - Hard Ground: 11.2 psi
  • Dual PVG-32 valves | System: Open-loop, pressure and flow compensated | Filtration Method: Single in-tank return filter
  • Variable displacement, axial piston | Fixed displacement gear pump | Track Drive: Closed-loop
  • Flow at Maximum RPM: 25.3 gpm (96.5 L/min) / 16.3 gpm
  • System Relief Pressure: 3,000 psi (206.8 bar) / 2,900 psi (200 bar)
  • Unit body construction
  • Feed opening: 60 in x 30 in (152.4 cm x 76.2 cm) | Infeed Roller Diameter: 28 in | Drum Diameter: 22.5 in / 27.3 in | Tip Diameter: 31.3 in | Drum Skin Thickness: 1.5 in / 1.3 in | Bearing - Inner Race Diameter: 4.3 in | Knife Thickness: .625 in (16 mm) | Shaft diameter: 5 in | Screen: .75-in (1.9-cm) thick | Screen Area: 3131 sq in | Center Retention Pin: 2-in (5-cm) diameter | Millbox Lid Liner: 16-in (40.6-cm) radius | dler Roller Diameter: 12 in| Idler Roller Bearing: 1-15/16, 4-bolt flange | Magnetic Drive Roller Diameter: 12.8 in
  • Maximum: 36.1 ft
  • Maximum: 8.2 ft
  • Maximum: 11.5 ft
  • Drum: 60.9 in / 60 in
  • Feed Table: 20 in | Of Cut Adjustable: .125 in (.31 cm) to 1 in (2.5 cm)
  • Feed Table: 60 in | Infeed Roller: 56 in | Millbox Opening: 60-in (152.4-cm) wide | Millbox Lid Liner: 62-in (157.4-cm) wide | Anvil: 13.6-in (34.5-cm) wide | Single Belt: 48 in
  • Loading: 6.4 ft | Millbox Opening: 30.5-in (77.5-cm) high | Millbox Lid Liner: 21.5-in (54.6-cm) high | Anvil: 6.1-in (15.6-cm) high | Load: 14 ft
  • Feed Table: 15 ft | Infeed Roller: 28 in | Center Retention Pin: 75.3-in (191-cm) long | Anvil: 73.5-in (186.7-cm) long | Single Belt: 20 ft
  • On Ground: 10.9 ft (3.3 m)
  • 18 in (45.7 cm)
  • 200 gal | Diesel exhaust fluid: 17.3 gal
  • Coolant Capacity (Engine and Radiator): 10.5 gal
  • Volume with filter: 10.8 gal
  • Feed Table: 4.6 cu yd
  • Tank: 20 gal
  • Fan: Flexxaire® (variable pitch) | Fan - CAC: Electric (variable speed) | Front Idler Roller Construction: Self-cleaning auger |Tooth Design: Serrated bars | Number of Teeth: 10 | Drive Planetary: 34.2:1 | Feed Roller Down Pressure: Adjustable | Number of Hammers: 9 | Number of Tips: 18 | Tip types: 18 | Number of Wipers: Four spiral fan | Useable Edges: One | Number of Pockets: 12 | Shaft Retention Type: Keyless bushing | Screen Type: Abrasion-resistant steel | Number of Screens: Two | Number of Sides: One | Anvil Type: Adjustable - replaceable wear surfaces | Return Roller Quantity: 3 | Motor Series: TH | Display Type: LCD | Switches Sealed: membrane CAN bus keypad | Track Type: D4 triple or double grouser | Type of Idler: D4 track roller | Number of Idlers: 9
  • 65000 lbs | Infeed roller with arm: 2700 lbs | Drum: 5370 lbs / 4707 lbs
  • Recommended: API CK-4, 10W-30 / Vermeer HyPower 68
  • V-belt | Design: 3-ply - 330# with V-cleat
  • Flare: Integrated with bolt-on corner flare | Infeed System: Steel | Drive Roller: Welded steel | Infeed Floor: Welded steel | Chipper Drum: A8 mod chipper steel | Millbox lid liner: Abrasion-resistant steel | Splice: R2 stainless steel cable
  • Feed: Welded slat chain
  • Double row spherical roller
  • 12 | Bolts/Knife: Two