2025 Vermeer® Trommel Screens TR5300EM 

Information

2025 Vermeer® Trommel Screens TR5300EM

TR5300EM highlights
  • Electric-powered efficiency
  • Quiet operation for wherever the job may take you
  • Complete control for overall jobsite confidence

Features may include:

Complete control
  • From either control, the operator can choose from four programmable presets or adjust machine settings based on incoming material.
  • Operators can control the machine through either the Vermeer DP10 display mounted on the control panel.
Convenient loading
  • The TR5300EM features a large, low feed height hopper that makes it easier to load with a loading ramp, making the trommel screen more mobile around the jobsite.
Maintenance-friendly
  • The hydraulic-driven chain drive system provides positive drum drive and allows the drum to lift off of the cog for service and maintenance.
  • From the dual-hinged doors on either side of the machine, you can perform machine maintenance efficiently through ease of access to components such as motor, trommel drum and drum drive.
Optimized end product
  • Without having to change out the drum, you can adjust the screen panel quickly which will allow operators to change opening size, wire gauge and type of wire so you can separate a wide variety of material.
Electric power
  • Powered by an industrial-duty, fully enclosed and fan-cooled electric motor. A single 60-hp (44.5-kW) motor powers the hydraulic pump stack. Electric motors reduce exhaust emissions, jobsite noise and maintenance compared to diesel.

Photos

Highlights

  • La Crete, Alberta
  • 2025
  • Vermeer®
  • Trommel Screens TR5300EM 
  • Available
  • Operation: 112.8 in | Head Pulley: 38-in (96.5-cm) | Self-Cleaning Tail Pulley: 38-in (96.5-cm)
  • Operation: 15 ft | Conveyor Belt Stacking: 15 ft

Specifications

  • 2025
  • Vermeer®
  • Trommel Screens
  • TR5300EM 
  • General
  • Siemens
  • 60 hp (44.7 kW) | AC panel: 75 hp
  • 177 lb-ft (240 Nm) at 1800 rpm
  • Conveyor Motor: 33 cu-in
  • Axle: Single leaf sprung
  • 445/50R22.5
  • Motor: 12 V | AC panel: 480 VAC, soft start | Motor rating: 480 VAC, 3 Phase, 60 Hz
  • Drum: 0-24 rpm | Fines Belt: 500 ft/min
  • Drum Operation: 0-30.9 gpm (0-117 L/min) | Conveyor Operation: 17 gpm
  • Heavy-duty structural tubing | Fines Conveyor: 2 in (5.1 cm) x 8 in (20.3 cm) structural steel tubing
  • Hopper Opening: 34-in tall x 37-in wide | Drum Diameter: 5 ft | Drum Support Description: Eight poly trunnion rollers 8-in (20.3-cm) diameter, 4-in (10.2-cm) wide | Thrust Bearing Diameter: 4 in | Thrust Bearing Face: 2.9 in | Drum Angle Adjustability: 0-7 deg | Brush Diameter: 14 in | Brush Assembly Support: Two 1.25-in (2.3-cm) sealed ball bearings | Head Pulley Type Rubber-lagged: 12-in (30.5-cm) diameter | Troughing Idler: 20-deg | Self-Cleaning Tail Pulley: 10-in (25.4-cm) diamater, with 2 7/16-in (6.1-cm) shaft | Head Pulley Takeup: 10 in | Self-Cleaning Return Idlers: 4-in (10.2-cm) rubber disc
  • 39 ft
  • 98.4 in
  • 13.4 ft
  • Operation: 89.9 ft | Drum: 15 ft | Fines Conveyor: 55 ft
  • Operation: 112.8 in | Head Pulley: 38-in (96.5-cm) | Self-Cleaning Tail Pulley: 38-in (96.5-cm)
  • Operation: 15 ft | Conveyor Belt Stacking: 15 ft
  • Bottom: 37 in
  • 9.5 ft (2.9 m)
  • Belt: 36 in
  • 100 cu yd (76.5 m3) per hr with 0.5-in (12.7-mm) screens installed and material with moisture less than 40%
  • 5.5 cu yd
  • Tank: 55 gal
  • Drum Drive Chain: 140 custom extended pin | Maximum Screen Panels: 4 | Head Pulley Type: Rubber-lagged | Troughing Idler: CEMA "B" with permanently seated bearings | Self-Cleaning Return Idlers: qty 8
  • 32000 lbs | Hitch: 11600 lbs
  • Bristle: Polyethylene
  • Conveyor: 220-lb, 2-ply, 3/16 in x 1/16 in, R2 splice