2024 Vermeer® Stump Cutters SC70TX

Information

2024 Vermeer® Stump Cutters SC70TX

Tough enough to withstand large stumps on a commercial jobsite.

The SC70TX can fit into tight spaces in a residential area. The track system is designed to decrease ground disturbance. The SC70TX is equipped with safety features such as the patented capacitance-sensing operator presence system and wheel brake to help you feel confident on the job.

Features may include:

Operator presence system
  • The operator presence system allows the cutter wheel to automatically stop when the operator releases the hydraulic cutter wheel controls.
Ground drive speed
  • The ground drive speed helps transport the machine between stumps to increase productivity on the job.
SmartSweep™ control system
  • The SmartSweep™ control system helps improve efficiency and productivity at the stump while helping to minimize wear and tear on the machine.
Gearbox drive cutter wheel system
  • Gearbox drive cutter wheel system directs the maximum amount of horsepower to the cutter wheel for optimal jobsite productivity.

Photos

Highlights

  • La Crete, Alberta
  • 2024
  • Vermeer®
  • Stump Cutters SC70TX
  • Control Station Description: Swing-out | Operator Vision Shield Description: Abrasion-resistant coated polycarbonate
  • Available
  • 129.5 cm
  • 182.9 cm

Specifications

  • 2024
  • Vermeer®
  • Stump Cutters
  • SC70TX
  • Stump
  • Integral motor and planetary unit
  • Upper: Straight bevel | Lower: Straight bevel
  • Track: Integrated into motor/planetary unit | Spring-applied and hydraulically released dual parking brakes
  • 950 CCA
  • Shutdown System: High engine temperature and low oil pressure | System Voltage: 12
  • High Travel: 2.6 km/h | Low Travel: 1.1 km/h | Cutterwheel: 948 rpm
  • System relief: 2900 psi (200 bar) | System relief: 206.8 bar
  • Bearing - Soft Ground: 29.6 kPa
  • Flow at Maximum RPM: 9 gpm | 34.1 L/min
  • Track Drive: Tandem gear pump, pressure balanced
  • Control Station Description: Swing-out | Operator Vision Shield Description: Abrasion-resistant coated polycarbonate
  • Track Frame Description: Tube and plate
  • Warning: Engine faults
  • Chip Containment: .7 cu m| Cutterwheel Cut Below Ground: 40.6 cm | Cutterwheel Cut Above Ground: 68.6 cm | Cutterwheel Straight Line Dimension: 165.1 cm | Cutterwheel Diameter without Teeth: 58.4 cm | Cutterwheel Thickness: 2.8 cm | Track Type: 9-in (22.9-cm) rubber iron core
  • 359.7 cm
  • 129.5 cm
  • 182.9 cm
  • Extended: 51 in | Retracted: 35 in
  • on Ground: 51.2 in
  • 1.6 L | Lower Gearbox: 2.1 L
  • Tank: 36.3 L
  • Engine Option One: 1769 kg
  • Number of Idlers: 10 | Display: Multifunction display (MFD); Displays - hours, fuel level, engine speed, engine faults and engine status | Driveshaft - U Joints: Two standard with double lip seal | Jackshaft Bearing Type: | Reversible Pockets: 30 | Directional Control: | Switches: Boom swing, boom height, creep propel, ignition, clutch, track gage, track speed range, SmartSweep, throttle | Controller: Vermeer C248 with SmartSweep | Quantity/Location: 2 | Sensor Type: Capacitive | Number of Pockets: 30 | Tooth Description: Yellow Jacket cutter system | Number of Teeth: 30 | Number of Indexes: 2 | Filtration Method: Full-flow 4 micron return filter, suction strainer | Cutterwheel Guard | Directional Control | Flow Control | Visual Interface | System Type: Tandem gear pump, pressure balanced | Driveshaft: 2 universal joints
  • SAE 75W90 synthetic gear oil | Lower Gearbox: SAE 75W90 synthetic gear oil | Recommended: Vermeer Hypower 68