2025 Vermeer® Stump Cutters SC402

Information

2025 Vermeer® Stump Cutters SC402

SC402 highlights
  • More power, more torque
  • Built with features for jobsite efficiency
  • Designed for serviceability

Features may include:

Efficient operation
  • The SmartSweep™ control system monitors engine load while providing continuous feedback, resulting in a smooth and consistent cutter wheel sweep rate that helps improve efficiency and minimizes wear.
  • The SC402 is equipped with a 40-hp (29.8-kW) Briggs & Stratton® Vanguard® engine with high torque output to help operators grind more stumps in less time and tackle more jobs each day.
  • With standard four-wheel drive, the SC402 was built to help prevent ground disturbance and minimize slipping – getting operators to the stump and back efficiently.
Jobsite flexibility
  • With options of either the Vermeer cutting system (VCS) or Yellow Jacket™ cutter system, operators can select the cutter wheel that is best suited to their operation and ground conditions.
  • Without the dual wheels installed, the SC402 is only 35.5 in (90.2 cm) wide, allowing it to enter narrow backyard gates and access tight jobsites.
Service-friendly
  • Designed for easy maintenance, helping you get back to work
  • Help protect your stump cutter investment with extended service coverage options.
Operator safety
  • A capacitive-sensing operator presence system automatically stops the cutter wheel when the operator releases the controls.

Photos

Highlights

  • La Crete, Alberta
  • 2025
  • Vermeer®
  • Stump Cutters SC402
  • EFI/ETC
  • Control Station Description: Fixed side
  • Gasoline
  • Available
  • 50.1 in
  • 53 in

Specifications

  • 2025
  • Vermeer®
  • Stump Cutters
  • SC402
  • Stump
  • EFI/ETC
  • Briggs & Stratton Vanguard®
  • 2
  • Gross (Maximum): 40 hp
  • 56 ft-lb
  • Dry-type safety element and restriction indicator
  • Spin-on
  • Medium: Air
  • Max Fuel Consumption: 2.2 gph
  • Gasoline
  • Electric clutch with brake
  • Fixed (Rear)
  • Spring-applied, hydraulic release at rear motors
  • 5.7 in x 8 in (14.5 cm x 20.3 cm) dual standard
  • 550 CCA
  • 20/50 Amp (rpm-based)
  • System Voltage: 12 V
  • Cutterwheel: 1525 rpm | Low Travel: 65 ft/min | High Travel: 130 ft/min
  • 107.6 dB(A)
  • System Type: Open-loop series system | Filtration Method: 10-micron fill strainer and 6-micron return filter | Flow Control: SmarSweep | Directional Control: Electric over hydraulic
  • Pump Flow at Maximum RPM: 6.2 gpm
  • System relief: 2470 psi
  • Control Station Description: Fixed side
  • Welded tube and plate steel
  • Maximum Angle of Continuous Operation: 25 deg | Cutterwheel Diameter: 20 in | Cutterwheel Thickness: .5 in | Cutterwheel Straight Line: 47 in | Cutterwheel Cut Above Ground: 24 in | Cutterwheel Cut Below Ground: 15 in | Jackshaft: 1.3 | Cutterwheel Shaft: 1.8 | Bearing - Secondary Belt: 1.8 | Degree of Oscillation: 12 deg
  • 118 in
  • 50.1 in
  • 53 in
  • Transport (without duals): 35.5 in | Overall Transport (with duals): 50.1 in
  • Transport: 53 in
  • Bearing: 1.3
  • Tank: 10 gal
  • Tank: 6.5 gal
  • Volume with Filter: 2.5 qt
  • Chip Containment: 7.5 cu ft
  • 1950 lbs
  • Tooth: Vermeer cutting system (VCS) | Number of Teeth: 18 | Reversible Pockets/Teeth: 16 | Jackshaft Bearing Type: Sealed ball | Steerable Axle Type: Hydraulic steering oscillating axle | Axle: Rigid (rear)
  • Recommended Oil: 10W30 | Hydraulic: Vermeer HyPower 68
  • V-Belt
  • Primary: 2 individual (matched pair) | Secondary: 6 Banded